The “AMS” name in the standard is an abbreviation of “Aerospace Materials Specifications”. The standard is published by SAE Aerospace, part. I am relatively new to being a provider of heat treat services and am trying to get some clarification on AMS D. The specification identifies. Does AMS D require a statement of compliance to the specification (AMS D). printed on, or provided with Certificates of Calibration for an instrument.

Author: Tejinn Akishura
Country: Finland
Language: English (Spanish)
Genre: Video
Published (Last): 26 March 2015
Pages: 382
PDF File Size: 1.78 Mb
ePub File Size: 8.22 Mb
ISBN: 465-1-82061-804-6
Downloads: 62272
Price: Free* [*Free Regsitration Required]
Uploader: Shaktikasa

A calibrated and traceable sensor with known deviations, if any, used for system accuracy tests.

thermocouples AMS | Pyrocontrole

mas Using the plane method, TUS sensors are located in a single plane perpendicular to furnace conveyance direction such that passing the plane through the furnace measures the entire work zone volume of the zones to be tested.

If additional copies are needed by other Alcoa employees, contact MQS. Product is tested to the requirements of the heat treat processing specification or to applicable requirements of other specifications. Sensors shall have a certificate of compliance that identifies the source of the calibration data, nominal test temperature, actual test temperature readings, calibration technique, and correction factor for each calibration temperature traceable to 7250d or other recognized National Standard.

Regardless of the calibration procedure used, it shall comply with the requirements of Table 3.

Signature for the testing company if not performed in-house? The difference is the arrangement and number of TUS sensors.

Using Honeywell X-Series paperless recorders for compliance with AMS D standards

Samples for tests shall be taken from the extremes and center of the load. Instrument Calibration also see Table 3 …………………………………… Instrumentation Records……………………………………………………….


A furnace containing a liquid that is heated to the desired heat treat temperature.

If the normal operation of the equipment in production is to load material into a cold furnace, preheating the furnace to perform the TUS is prohibited. Identification of technician performing the test? Sensitivity as required by Table 3, Note 4? If subsequent internal instrument adjustments or offsets are made to achieve TUS requirements, these internal adjustments or offsets must be applied during subsequent SATs per 3.

All readings of all TUS sensors and control or recording sensors are within the temperature tolerance requirements shown in the applicable Table 8 or 9 during the soak period except as allowed by 3.


Equipment used for the thermal processing of materials and parts. Instrumentation Type E ………………………………………………………. Frequency shall not be reduced until the specified number of successful consecutive tests in Table 8 or 9 have been 2750v. Any intentional offset as left?

Survey with 10 to 16 sensors 1 failure? Existing installations at the release date of this revision do not require recording instruments. The equipment shall not be used for additional processing until the cause has been corrected and the TUS has been performed successfully.

Currently, the 2750e capability works only on single zone thermal processing equipment. A sensor connected to the monitoring instrument.

Process instruments of thermal processing equipment shall not be used to record TUS sensor data. Output of sensors shall be converted to temperature readings by instruments specified herein or instruments of equal or greater accuracy. Reuse of any thermocouple is prohibited unless the insulation remains intact and wires including the hot junction are not damaged.


Continuous furnace throughput speed shall be that normally used for processing. For retort furnaces where a sensor in the retort is used to control temperature, the temperature variation 2750 with respect to the sensor in the retort and not to the furnace set temperature.

In addition, any offsets or adjustments shall remain in place during all subsequent heat treatments in the temperature range where the offsets are applied. Instrumentation Type B amz.

AMS2750D Standards Compliance with X-Series Recorders

SAE invites your written comments and suggestions. These are necessary to ensure that parts or raw materials are heat treated in accordance with the applicable specification s. Technician who performed the calibration?

Connectors, plugs, jacks and terminal strips are permitted if they are the compatible type, i. When the hottest and coldest temperature locations change within the furnace based on the final readings from the most recent Temperature Uniformity Surveythe recording sensor locations for types A and C instrumentation may need to be moved within the furnace to reflect the new hottest and coldest locations within the work zone. Control instrument tuning parameters? Performed to assure the accuracy of the furnace control and recorder system in each control zone.

Survey with 6 to 9 sensors 1 failure?