DIN EN ISO 7253 PDF

Buy DIN EN ISO PAINTS AND VARNISHES – DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) from SAI. DIN EN ISO Paints and varnishes – Determination of resistance to neutral salt spray (fog) (ISO ); German version EN ISO Draft standard [WITHDRAWN] DIN ISO – Draft. Paints and varnishes – Determination of resistance to neutral salt spray (fog) (ISO.

Author: Dujind Tuktilar
Country: Thailand
Language: English (Spanish)
Genre: Education
Published (Last): 8 July 2010
Pages: 387
PDF File Size: 12.55 Mb
ePub File Size: 16.11 Mb
ISBN: 947-5-55066-274-5
Downloads: 31924
Price: Free* [*Free Regsitration Required]
Uploader: Vibei

Adjust the pH using the procedures described in 753. Assessment of degree of flaking DIN EN ISOPaints and varnishes — Evaluation of degradation em coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 8: George Gorecki – Naperville, Illinois A.

Nevertheless, the method described gives a means of checking that the comparative quality of a metallic material, with or without corrosion protection, is maintained. So if you want to know how to set up a salt spray cabinet or how to make the salt solution, then B is a reference.

General introduction and designation system ISO The sodium chloride shall contain less than 0,? It is often not possible to use results isl from salt spray testing as a comparative guide to the long-term behaviour of different coating systems, as the corrosion stress during these tests differs significantly from the corrosion stresses encountered in practice.

ISO – Paints and varnishes — Determination of resistance to neutral salt spray (fog)

Well done to Anthony Thresh from Hodgson Sealants! Subtract this number from the initial mass of the reference specimen 72253 to testing, and divide the resulting number by the area of the exposed surface of the reference specimen to assess the metal mass loss per square metre of the reference specimen.

If the coating on the back or edges of the panel differs from that of the coating product under test, it shall have a corrosion resistance greater than that of the coating product under test.

  ATO INFRACIONAL E SUAS VICISSITUDES PDF

As a complement to reference-metal specimens made of steel, high-purity zinc reference-metal specimens may also be exposed in the tests, to determine the corrosivity against this metal as described in Annex B. Check the pH using electrometric measurement or in routine checks, with a short-range pH paper, which can be read in increments or 0,3 pH units or less.

It particularly applies to: The temperature shall be measured at least mm from the walls. But which, is any, accelerated test is appropriate depends on what the finish is, and what you hope to test against.

Corrosion resistance

Brian Terry has directly answered your question, but please post your situation rather than an abstract question so that readers can best help you.

Therefore, the test results should not be regarded as a direct guide to the corrosion resistance of the tested metallic materials in all environments where these materials might be used. The method differs from the standard salt spray tests in cin the salt solution dij in the prohesion test is much more dilute and the panels are e exposed to it continuously. Assessment of degree of cracking ISO Options include the following:.

Resistance to Salt Spray. For chemical cleaning of the zinc reference specimens, use a solution of saturated glycine, ? Thickness esin micrometres, of the dry coating sand method of measurement in accordance with ISOand whether it is a single iiso or multi-coat system see C. Tikkurila finalises first quarter of with revenue growth 4th May Read more. It’s not possible to diagnose a finishing problem or the hazards of an operation via these pages.

The reference specimens shall have dimensions of 50? A isk Schematic diagram of one possible design of spray cabinet with means for treating fog exhaust and drain a??? If the coating on the back or edges of the panel differs from that of the coating product under test, it shall have a corrosion resistance greater than that of the coating product under test.

The compressed air supplied to the atomizers shall be diin through a filter to remove all traces of oil or solid matter, and the atomizing pressure shall be at an overpressure of 70?

  FX 900LCD PDF

The appropriate temperature depends on the pressure used and on the type of atomizer nozzle and shall be adjusted so that the rate of collection of spray in the cabinet and the concentration of the collected spray are kept within the specified limits see? Possible changes in pH may result from loss of carbon kso from the isoo when it is sprayed.

After cleaning, rinse the reference specimens with fresh solvent, then dry them.

The salt spray methods are all suitable for checking that the comparative quality of a metallic material, with or without corrosion protection, is maintained. It also describes the method employed to evaluate the corrosivity of the test-cabinet environment.

Equivalence between ASTM B-117 vs. ISO 9227 NSS

BS F4 Scope and Field Application This standard gives an indication of how well a painted surface will resist artificial seawater spray. After each immersion step, thoroughly clean the reference specimen at ambient temperature by kso with water and by light brushing, then by rinsing with acetone or ethanol, followed by drying. Ein have a customer, that we supply some zinc electroplated mechanical components to. I suggest that you send some parts out for testing according to the ISO standard to see if they meet the spec.

The quantity of liquid paint we needs depends on the method of application.

Therefore, the test results should not be regarded as a direct guide to the corrosion resistance of the tested metallic materials, in all environments where these materials may be used. For dated references, only the edition cited applies. In addition, for quality control purposes, comparison can be made between specimens coated with the same coating.